Roll forming machine for main tee and cross tee

Basic Info

Model No.: CNZT002

Diameter Of Shafts: Φ60mm

Main Power: 3kw

Drive Mode: Gear

Material Of Rollers: GCr12MoV

Number Of Rollers: 20 Rollers

Voltage: Customize

CUTTING Power Supply: Hydraulic Power

Language: ENGLISH Or Customize

Function: Ceiling Building

DECOILER Loading Capacity: 5 TONS

Additional Info

Packaging: 20ft container

Productivity: 25m/min

Brand: Zhongtuo

Transportation: Ocean,Land,Air

Place of Origin: China(mainland)

Supply Ability: 5 sets per month.

Certificate: CE/ISO9001

HS Code: 8455221000

Product Description

Roll Forming Machine for main tee and cross tee

Roll forming machine for main tee and cross tee, there are two types: fully automatic machine and half automatic T bar machine. Fully automatic flat T bar machine is developed to make ceiling T bar fully automatic without people to intervene. For making the whole set ceiling T gird, you need to make main T, cross T and wall angle roll forming machine. The machine is composed by the following elements: decoiler, hydraulic punch press, feeding device, roll forming machine, straightening device, hydraulic cutting off, cold water recycling device, pneumatic and electric control system, etc.
Here are some normal T sizes for your reference:

T bar

1. Decoiler

Bearing 3 Ton
Inner diameter φ450-530mm
out diameter φ1200mm

Quantity: 2 sets

decoiler

2. Feeding device: synchronism adjusting rollers.

entry beach

3. Punching Machine

This line equipped with fully automatic hydraulic punching machine.

shearing and punching system

4. Roll Forming Machine

Roll Forming rollers: material GCr15, hardness after heat treatment HRC48-50, hole diameter (roller shaft diameter) φ42mm, the min. outside diameter of rollers isφ100.

T grid rolling forming machine

5. Transmission Device:
a. Main motor, Frequency control.

b. The driving rollers are driven by three sides belt, the passive rollers are driven by gears, with center distance a=75, reduction ratio i=30 worm gear case, gear mould m=5. Main side plate thickness: 30mm, deputy side plate thickness: 25mm. Finished by six sides grinding and boring holes treatments.

c. The material of main shaft is 40Cr, finished after heat treatment and refine grinded.

6. Hydraulic Cut Off device
a. Hydraulic system: the system has unloading protect function.
b. Mould rack: the mould plate closed height is 260mm; the adjustment range of the closed height is 20mm, the max. Stroke of oil cylinder is 100mm.

c. There is straight guide track under the mould rack, the relocation of the mould rack replying the push of buffer pneumatic cylinder.

d. The cut off mould: design as the botch of the production, equip with another cut off mould.

7. Electric system

A. Use frequency converter, centre auto control, uses the fixed rule to adjust the length and automatic cut off. When the punched mould is cutting off, the roll forming machine lower speed automatically, when the cut off is finished, it goes to high speed again.

B.PLC is composed by human-machine interface, button, switch, emergency stop, etc. Multi- languages supported. You can specify length, pieces and others in the PLC

C. Alarming function: stop when lacking material, count the numbers, stop when the production number is finished, alarming when transmission failure, emergency stop, mould stuck, position limited, etc.

Note: Installation of electric components obeys local rules. All the electric components have clear marks. In the electric cabinet, we use anti-flaming plastic slots to arrange the wires. The number of the wires is clear, the layout of the components is reasonable, the control panel is tidy, the marks are clear.
Working Environments

1) Power supply: voltage 380V±10%/ three phase four wire, frequency 50HZ.

2) Total power: 12kw

3) Air rate: 10.0L/min (air pressure 0.4-0.6Mpa)

4) Environment temperature: 0°C-40°C, relative humidity: 60-95%RH.

T bar rolling forming machine

Other sizes of the T bar for your reference:

32H Model
I) Main tee: 32mm x 14.5mm x 3.0m, or 3.05m, 3.60m, 3.66m
Ii) Cross tee: 32mm x 14.5mm x 1.2m, or 1.22m
Iii) Cross tee: 32mm x 14.5mm x 0.6m, or 0.61m
Iv) Wall angle: 20mm x 14mm x 3.05m, or 3.60m
V) Thickness: From 0.23mm, 0.25mm, 0.28mm, to 0.30mm and 0.40mm
T grid series
38H
I) Main tee: 38mm x 14.5mm x 3.0m, or 3.05m, 3.60m, 3.66m
Ii) Cross tee: 38mm x 14.5mm x 1.2m, or 1.22m
Iii) Cross tee: 38mm x
14.5mm x 0.6m, or 0.61m
Iv) Wall angle: 20mm x 14mm x 3.05m, or 3.60m

T size



Looking for ideal Roll Forming Machine Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Main Tee are quality guaranteed. We are China Origin Factory of Cross Tee Machine. If you have any question, please feel free to contact us.

Product Categories : C/U/ Channel & T Bar Roll Forming Machine > Drywall Profile Roll Forming Machine

Product Images

  • Roll forming machine for main tee and cross tee
  • Roll forming machine for main tee and cross tee
  • Roll forming machine for main tee and cross tee
  • Roll forming machine for main tee and cross tee
Email to this supplier
  • *Subject:
  • *Messages:
    Your message must be between 20-8000 characters